Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I am using st-link debugger with NRF51822 module.
I was trying to connect it openocd, but it failed. st-link is working with STM32 processor and able to flash through...
Hi,
I found a suspicious line of code.
SDK: nRF5 SDK 13.1.0 (7ca7556)
File: peer_data_storage.c
Function: pds_peer_data_read
At line number: 415
if ((*p_buf_len...
Hi,
I made a custom board with nrf51822 and custom antenna which works fine for examples which use SDK10 + SD110.
For my application it was recommended to use SDK12.3...
Hello,
i am working on a rotation counter, i am using adc and LPCOM with nrf52832 DK board.
but LPCOM code is not working.
static void lpcomp_event_handler(nrf_lpcomp_event_t...
Hello every one,
I'm using nrf51822, for some calculation, I have to use logarithm.
is there a possibility to directly use this function by nrf51822?
I already applied...
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I used the reference design file provided by Nordic (NRF51x22_qfax) but added the following...
I want to run the HID Mouse and Keyboard examples on nRF51 Dongle. How I can configure it first, to connect with my PC via Bluetooth and second, to configure the GPIOs act...
From document [Getting started with the nRF52840 Preview Development Kit]
( www.nordicsemi.com/.../Getting-started-with-the-nRF52840-Preview-Development-Kit)
we know that...
Hi,
I'm looking for a BLE device to work with an arduino and to speak with a smartphone.
The point is that the connection should be made by the user via the smartphone...
I am using nrf52 with sdk11. I have set the advertiser data as Manufacturer data in nrfConnect app in my android phone. So that whenever the data from my phone is advertised...
Hi.
I try run "ble_app_hids_mouse" example from nRF5_SDK_11.0.0 in nrf51422 (nrf51 dongle).
Previously i ran this example in nrf52 (nrf52 DK, s132 SoftDevice), and all worked...
Hello!
We use chip nrf52832(QFN-48) in our project and we wont to pass the PCB certification.
But we also want to use chip nrf52810(QFN-48) in another project, but with...
Hi ,
Please advise, what the Low Power option I have if I want to sample Two channels of analog input at the same time. The sample rate in every channel is 12K, 12Bit....
Hi I am using SDK12.2.0 and Softdevice S130 v2.0.1 on board PCA100028 ; the board works fine and Phone can scan the name of DFUtarg； But when run the same on the customer...
