Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
How do you do
Now use the Nordic nor51822 \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this routine plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples...
Hello,
Am working on NRF52 interface via SPI to Micron N25Q flash .
Am able to identify flash by reading chip identification correctly and after this to test memory writing...
We are a small R&D team and we are currently developing a medical wearable. We are using nrf52832 and we are generating approximately 54kbps (6.75kBps). I 'd like to ask if...
Hi!
After reading few posts about spi slave/master issues... I'm also challenging with one of them. I have following setup nrf51822, s130 2.0.1 and sdk 12.3.0… nrf51 (spi...
I am working on OTA DFU about nRF52810.
My refernece project are ble_app_uart\pca10040\s132 and bootloader_secure_ble\pca10040
I find that the RAM start address between...
Hello im trying to create a single master connected to multiple slave to make synchronous movement for my robotic arm project but im not entirely sure which Bluetooth to consider...
Hi,
I am running the BLE DFU example. I am able to perform the DFU OTA implementation successfully. The problem I am facing is that, once the application has been updated...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello,
I used translation software.
I am measuring current.
I want to enable dc-dc mode.
how to enable the dc-dc?
also,where should I change the source code?
I...
Hello folks, we are currently using RedBear Lab Arduino toolchain to develop a MDBT40 based application. However we meet a lot issues on merging bootloader.hex (downloaded...
Hi,
Since I'm having a hard time understanding this through the SDK docs, I'll ask it here.
I'm currently using a BMD200 module (from Rigado) which uses a nRF5188.
...
I have a BLE-Nano v1.5 board with 32KB of ram starting at address 0x20000000 (til 0x20008000). However when I want to read a byte of the uper 16K (0x2004000+), I get a 'cannot...
I need to scan for nearby beacons.
This was featured in the mbed examples but does not seem to be described anywhere else
I am using SDK12 at the moment.
I found the...
hello
Now I use the nRF52832's board and I was measuring the current
But when the board's power is off and i measured, the current was flowed in the board.
Now i am using...
Hi!
I can't start project with OOB bonding. If I set settings like just works (MITM = 0, OOB =0), all works correct. But I need more security for bounding. For this reason...
