Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hello,
I am using the Nordic NRF 51822 chip and are am wondering if full Eddystone support can be found in the latest firmware? I have read on github ( github.com/.../nrf5...
Hi,i m working in uav project with nr52 and GY-87 that contains mpu6050 and hmc8553 as sensor. i use i2clib to do connexion with twi created by jeff rowberg, then i wrote...
Hi,
I'm trying to add Openthread support to my project, which is based on ATT_MTU_Throughput example. I followed the tutorial in infocenter, but I still have some problems...
Hi,
I am attempting to run the various USB example programs on the nRF52840-PDK USB, but my nRF usb device is not being recognized (in windows OR linux device tree). Is...
Hi.
I just spend 2 days debugging problem with dfu. In the function nrf_dfu_app_continue the function nrf_dfu_flash_store is called with len parmeter as bytes and should...
Hi, I would like to control 2 LEDs independantly with the same server node. Should I try to [1] add a element with the same simple on/off model in that server node OR [2]...
Hi,
I'm running an ADC sampling every 8msec, sampling the output value of an op-amp as well as a reference voltage. I subtract the two in firmware. I was implementing the...
Hello,
I am using SPI interface to communicate with a sensor BMI160, looking into the driver for BMI160 I can see how the low level functions for reading/writting are used...
Hi,
i am trying to upload the code to BLE 400 from waveshare from nrfGo by getting the hex file from this library
While Trying to upload the code i am getting the following...
onkey_full_20170814.hex
onkey_0000.hex
onkey_boot_s132.hex
This time 14.0 sdk was updated.
There was a problem after the update
Problems when uploading bootloader...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51 controller.
I am using muliple nrf51 devices to connect each other and share sensor data with each...
I'm using a pin for trigger switch input with the following codes
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;...
Hi,
I would like send serial data in both directions (like by RS-232) between BMD-300 Evaluation Kit and BLED112 dongle.
I'm a beginner on this subject, so I'll ask...
Hi,
i am working on custom nrf52 board which is operating by Li battery of 3.7v 27mAh battery. now the battery is dead i didnt find 27mAh batteries in the market near to...
