When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I am trying BLE multirole application ble_app_multirole_lesc from the SDK 13.0.0.
I am using nRf52832 DK along with GCC toolchain.
For debugging I am using Segger...
In the mesh network, the sender uses trickle algorithm to control the repeat sending process, and at last the sender will send the message forever in a max interval at a handle...
Hi Nordic Team!
After developing our firmware on the nRF52 HDK, we designed our custom board, and we're starting to write our custom board configuration file.
The main...
Hi,
we've developed a custom board with nrf51 and use bonding and white listing.
Everything works fine when connecting and bonding iOS phones with this devices but with...
HEllo,
I was wondering whether or not is advisable to use the same handler to handle transmission/reception of data over SPI0 and SPI1 interfaces.
I have two sensors...
Hello
I am using a custom board, based on nRF52832 CIAAB0. I have also S132 installed, and I am using SDK 13.1.0. TWI pins are P0.16 - SCL & P0.18 - SDA. The code is based...
I am trying to advertise some data using the s130 softdevice to my MS49SF2 (nrf51822 based module ) and then flashed the hrs example code to it..
Still I couldn't find...
hi, Nordic
I'm using your nRF51-DK(PCA10028) board, on android, i disconnect connection by call BluetoothGatt.disconnect ( developer.android.com/.../BluetoothGatt.html ,...
Hallo i am beginner developer, i plan to send sensor data to smartphone, i am still confused whether to use ble_app_uart or advertising mode, for example my case saw TrackR...
Currently I am using the spis driver to send data through the SPI peripheral. On the event handler I want to capture the time in which the chip is selected, which in the case...
I just opened my nRF52 DK and tried to flash the board. I got the error
ERROR: There is no debugger connected to the PC
Most concerning is that the LD5 light does not...
I have two nrf51-DK's (say A and B).
A , nrfStudio doesn't detects it.
(Windows doesn't even shows USB port connection in device manager, so cannot try nrfjprog -...
Hello dear community !!! I have long wanted to try the nordic chips. I took nrf52840 -preview dk and arducam. I'm still not very familiar with working with the nordic chips...
Hello,
I'm having latest nRF connect for Android v4.13.1.
I'm running it on Samsung S6 (model SM-G920F) Android 7.0 nougat;
build version (NRD90M.G920FXXS5EQG); Kernel...
