Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...
I use the nRF OpenMesh from the GitHub. ( https://github.com/NordicSemiconductor/nRF51-ble-bcast-mesh )
My mesh network just has two mesh node, node A and B.
I made A...
Hi everyone!
I want to work with two UART interfaces in my nRF52DK, in one hand, I must receive data sended by one cable which converts USB to serial, for this I use this...
Hello,
I caused a hardfault error and triggered the HardFault_Handler in "hardfault_handler_gcc.c". But instead seeint its source, I could only see the message no source...
When I start the nRF51822 sniffer ble-sniffer_win_1.0.1_1111_Sniffer.exe I get the following message:
!!Your firmware is outdated!!
Please upgrade (press CTRL-R).
When...
Hi team,
I am using sdk 12.1.0 and ble_app_hrs_c example.I enabled #define NRF_LOG_USES_TIMESTAMP 0 to 1 and iam usng nrf51822 dongle.my program gets hanged.I need to print...
Hi all,
I use the example of examples/ble_central/ble_app_multilink_central/ to test the connect timeout event. When it scan the peripheral and try to connect it, power off...
Hi, I am wondering why, sometimes, I get an odd packet out of order on the receiver. It is very random, it can occur at anytime, though usually it takes a minute or two. Testing...
So, does anyone have practical advice for reducing the code size of peer_manager and related modules, so that the ble_app_template project fits on the nrf51822 128KB part...
I am having an Windows 10 64bit OS. I am using PCA10000 board as sniffer. When i try to use it, I am getting Try plugging out the hardware error. Even CTRL +r is not working...
