Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi Nordic DevZone !
I'm facing an issue that I cannot manage to fix by myself.
So here is the brief: I'm trying to create a BLE beacon that will send some analysis results...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
i am working on controlling rgb led with nrf52832 using ble which is based on ble_app_uart example script so my script is working properly on your development board everthing...
Hi,
I want to measure the current draw of the MCU only on the nRF52840DK while I am running my custom code. I want to exclude the current draw of all components except for...
Hi,
I’m currently working with the nRF52833 together with the nRF21540 Front-End Module (FEM). I have configured the FEM to provide a gain of 10 dBm. I have a few questions...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Custom PCB with nrf5340/nrf7002. Currently was using NCS2.9.0, with WPA2-PSK connection to the wifi.
While trying to enable use of WPA2-Enterprise, I updated to NCS3.0.0...
I want to use Nordic 52840 DK (Bulb FW) as DUT to setup Matter Certification test.
I have completed below steps:
1. Flash Raspberry Pi (Ubuntu Server 24.04.2 LTS (64-bit...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hi,
does the Azure functionality in the nrf connect SDK support the SAS authentication? I need to connect only with the SAS key, and as far as I can see, that's not possible...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi Q&A My keyboard chip is NRF52832, and the program uses ESB 2.4G communication. The receiver dongle uses NRF52833. Now there is a problem that when the CAPSLOCK is clicked...
Dear All,
In our company, we have replaced the NRF52811 (ublox module) with NRF54L15 (raytac module) for new batches of products.
The fw is a simple BLE to UART bridge...
I am using 2.9.1 toolchain and sdk with a custom nrf5340 board and trying to use High Voltage (HV) with DC-DC mode. I don't know much about it as I have been using a nrf5340...