Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I have few questions that weren't addressed either in the infocenter or in the devzone:
In which way app_timer uses CC registers? Each running timer use one of these...
I want to transfer the code from nrf51822 dk board to a beacon kit, after connecting the beacon kit to the dk board, then I change PCA10026 to PCA20006 on the C/C++ define...
i was trying to send acceleromter values of mpu9250 to pwm pins. for this i have merge to different examples i.e. nRF-mpu-simple and pwm library example. but it showing error...
Hi,
I'm a beginner of BLE and I did everything from the three BLE tutorials, that uses sdk 11. However when I try to do it in sdk 12.3 it doesn't work, because there are...
Hello,
I am using ble_app_uart code. My first goal is to execute a function when board connects with an android device. Another goal is to disconnect board from an android...
When reading about access_opcode_t struct on its infocenter page it stumbled upon this table i don't understand.
access_opcode_t is defined as:
Data Fields
-------...
I'm employing 51822AA.
I need to debug firmware for this chip line by line. Like environment of ARM9 with Lauterbach TRACE32 through JTAG.
Is line debugging possible...
From application point of view, when should I use UICR and when should I use Flash storage? I have studied the documentation and the functionality seems very similar. The...
Hi everyone,
I trying to make a flash jump on Nrf51822 in my project. there are 2 programs(program A and program B) below. i am working on to make program A jump to program...
Hi everyone,
I'm new with nrf52832, and I need to measure elapsed time in microsecond between rising edges of 12 different Gpios. I have 12 piezoelectric sensors filtered...
Hi,
I have used nRF52840-PDK.
And I want to test profile and protocol with PTS.
I succeeded in GATT-based service test and GATT test with PTS.
But when I try to L2CAP...
How do you do
Now use the Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this plus Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ peripheral...
I try to add default nRF sdk libs in Segger studio. All files exist and path corect.
in nutshell i try to add uart module to default ble_app_buttonless_dfu example
Hi ,
I'm looking for BLE Specification but I just found NRF52 Datasheet on Nodric page . Can you give me this document , It will help me a lot . Regards !!!
Hello All
I am planning interface the BLE peripheral + Capsence(Atmel QT111) board
i did the Capsence Board with Spi Protocol..then second phase i has to implement with...
