Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello, I started working on BLE mesh using nrf52832 QFAAE1. from hardware side i have custom self design nrf52832 QFAAE1 lot's of board, and every board working, i verify...
When I add an attribute with BLE_GAP_CONN_SEC_MODE_SET_OPEN I get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event when I try to read it.
I do not however get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
My application involves driving a digital-output (PDM) MEMS microphone at 1 -- 3.25 MHz with a clock generated on a GPIO.
devzone.nordicsemi.com/.../
The output of the...
Hi, I have a custom service with 3 characteristics and i've been attempting to send one of them as a notification so I can use it in the HRS sensor app by changing the UUIDs...
Hello,
I am working with the nRF51822 and S110 Softdevice. I have so far successfully created several examples of fairly complex Peripherals. Now I am trying to,
A)...
Hello,
If we use same hardware and antenna design of one of Nordic DV/EV kit, can we shorten bluetooth LE certification process?
I see Nordic points the following app...
Im trying to run the example blinky_example on BLENano (tried with gcc / nrf51822-sdk on linux and windows)
.hex from linux before merge : 8475 bytes
.hex from windows...
I'm looking at the downloads for the nRF51 DK which has the nRF51422 core. I'd like to put the s110 softdevice onto it, but I don't see a download for s110 on nrf51422, just...
Hello,
I am trying to use the s120\multilink_central example, using SDK v6.1 and S120 v2.0. The probleme is that I get a hardfault handler. I think that the probleme is...
Hi, I am using a nrf51822 with sdk 7.2.0 and s11o v7.1.0
I also have a imu ( mpu 6050 ) that gets accelerometer and gyroscope data.
How do I do continuous transmission...
Hi,
I am using the nRF51 Dongle and every time I send a command the pipeline goes into "Stall" condition. Using USBlyzer I can see that the command is sent but straight...
Hello,
I would like to build a device that looks for other beacons (not using a phone)... This device would simply look for other beacons near this device.
My questions...
I just tested putting the same firmware on two different nRF51822 s and inspected them with this test app .
They show two different UUID's.
I can find no macro...
Hello guys!
I'm experiencing some troubles trying to compile the blinky_rtx example for my new nrf51DK. The source is taken from the SDK7.2.0.
I'm under Linux and I...
I am brand new to nRF51 DK and I am struggling to figure out where to start. My goal is to periodically sample analog inputs and write them to SD card.
Can someone point...
