Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I am using a nRF52832 DK(PCA10040). I am qurious about the output impedance at RF connector "J1" on the PC board. Does it provide 50 ohm output impedance so we can...
Just two questions regarding the new nRF52840 to make sure I've understand it correctly;
For the NFC, this is passive only? So it acts like a tag and is not able...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...
Hello!
I'm trying to use the ram_retention in sdk 15 alpha to retain RAM in system off mode and do some power profiling.
The default code seems to retain 8 kB of RAM...
My project needs to use 2 different TWI instances and 1 SPI instance. I knew that it is not possible to use three instances at the same time in nRF52.
To implement 2 TWI...
Hi Nordic,
I am trying to enable the DC/DC converter on a PCA20006 rev 1.3.0.
I am using the softDevice S130.
1. Using the sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi.
I am using saadc example code or SDK V13 with the following requirements:
Voltage input up to 70mV,
Resolution: 50uV
So I did some modification to support...
Hello,
yesterday I got a Thingy:52 device at an event held in Frankfurt/Germany. At home I've tested the DFU for the latest firmware and observed that the image was transfered...
