Hello,
We can not convert Altium File to DipTrace or Eagle File. We need those files asap. I'd be thankful if you could help me in that issue.
Thank you
We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi,
I have a device with nRF52832 and firmware is composed of Bootloader (BL), softdevice (SD) S132 v2.0.0, application and I am using SDK 11.0.
I have created different...
Currently, we are trying to have the nRF51 chip working with a type of capacitive pressure sensor. We did quite a lot of work on searching proper circuits of reading the capacitance...
I have 2 board nrf52840 DK, I now I want to send file ( 1~2 Mbyte) from board_1 to board_2 without use UART. where can I get example to do that ?
PS: I also need example...
I've merged the experimental_ble_queued writes sample code into my project and am testing the long write characteristic with nrfConnect from an Android phone. I get no errors...
Hi,
I am trying to figure out the reboot reason on an NRF52 in order to solve it in the best way.
We have a design with a dual supply 3.6V/5V going through a 3V LDO...
Hello,
i have a BLE Peripheral that has a service that we use to simulate UART over BLE. Very similar to the nRF UART. I consider the time to establish a link that allows...
Hi all,
I am trying to save an UART variable I am receiving. My case is very similar to the example Flash Write Example, but I would write few bytes instead of the whole...
Hello!
I have to sample audio signal from a microphone (MAX 9814 adafruit) with the nrf52 board. I use the saadc and then I perform a FFT of the data using the sdk 13 examples...
I implemented my profile based on GLS example. my profile has five services and every services have several characteristics. Pairing with several smartphone work properly...
hi,
I would like to use pwm to output the 1HZ waveform to drive the motor, but when I set the frequency to be 1HZ, I can not find the device and cause 51822 to reset.
This...
Hello, I'm working with the NRF6310 Motherboard and play with it a little with SDK 6.1, but i want to create profiles with the Bluetooth Developer Studio, so I started using...
I download "nRF5_AirFuel_SDK_2.2.0_7b89a57" and use "ptu_app_beacon" development, I am currently using "nrf51822-QFAA" and "nrf51822-QFAC", how do I set up IROM and IRAM?
Hello iam using softdevice 110 and SDK 10.0.0, Iam trying set tx power of nrf51822 using function sd_ble_tx_power_set(), i have tried 0dBm and 4dBm both are giving same RSSI...
wqewqeqwe.PNG I want to program the nrf52 chip using J link Edu -SWD mode. I actually connected the SWDCLK, SDI, and Vtref and GND of Jlink EDU programer to SWDCLK,SDI,3.3V&...
