void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I am using nRF 52 DK with Softdevice s132 v4.0.2 and app ble_app_uart from sdk 13.0.0
When i try to connect using nRF Toobox running from my Nexus 6p Android phone Segger...
Hi all!
I write for nRF52 but I can't to understand it. There are two cases:
first- I want bound my peripherial with central. And in future I want connect only between...
Hello iam using softdevice 110 and SDK 10.0.0, I have created project using ble_app_uart example code, i have added device manager APIs to manage bonding. Problem is iam GATT...
Basically, it can be divided into two cases
Reading/sampling TX pin of the sensor (since usually nothing is sended back)
Send/Read possibility - in case of range switching...
Hi all, today I was working properly and, in a second my nRF52382 (I use SD s132 V3.0 without bootloader, and SDK 12.2) is "disappeared". I googled and I've found some cases...
I am using nrf51822 with 16k RAM chip, xAA.
I followed the procedures...but I don't know what is wrong with it..
Program secure bootloader with S130 (2.0.0), SDK...
Hello,
I am trying to use the new nRF Connect 2 for Desktop. After installation, the app gets stuck and doesn't show any GUI. Investigating the network shows that the app...
I have been setting up systems to develop nRF52 code for the better part of two years. Maybe I am getting forgetful in my old age, but I can't seem to get it working this...
Hi.
I am looking for appropriate 2.4Ghz Nordic RF chipset.
I have studied 2.4Ghz chipset. but so clearly show about
1:n audio streaming (mono or studio)
exactly what we...
Hi, we are using nrf51822 xxAB based module and would like to understand which SD/SDK combination is best to use in terms of memory usage. We have developed original firmware...
I'm in the process of migrating from SDK11 to SDK13. I have a custom UUID with 3 characteristics (2 notify chars for data and 1 r/w for sending commands), based off HRS and...
Using SDK 12.1.0
I2C with SoftDevice works on PCA10040 Eval Board with nRF52832 but
hangs in the nrf_drv_twi_enable function with TY module EBSGCNZWY which is an
nRF51822...
Attached program has 4 characteristics
UUID_VLEN1 - VLOC_STACK, no rd_auth or wr_auth - value can be read after written
UUID_VLEN2 - VLOC_USER, no rd_auth...
Hi guys,
I'm receiving the following errors whilst trying to setup to the Crypto library on nRF52:
............\components\libraries\svc\nrf_svc_function.h(72): error...
