Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello.
I have some questions. Is it possible stabile work of android device , that has bluetooth 4.0 , with nordic device on base softdevice s132 v 5.0 ? What should i...
We're thinking of using the 52840 to capture and stream 4 vital signs per patient to a nurse's monitoring station. BLE/MESH would both work. Is there an off-the-shelf, desktop...
Hi all,
I am currently building an app that does HTTP requests to Strava ( strava.github.io/.../).
Before going deeper into the SDK, I would like to know if it will...
I have few questions that weren't addressed either in the infocenter or in the devzone:
In which way app_timer uses CC registers? Each running timer use one of these...
I want to transfer the code from nrf51822 dk board to a beacon kit, after connecting the beacon kit to the dk board, then I change PCA10026 to PCA20006 on the C/C++ define...
i was trying to send acceleromter values of mpu9250 to pwm pins. for this i have merge to different examples i.e. nRF-mpu-simple and pwm library example. but it showing error...
Hi,
I'm a beginner of BLE and I did everything from the three BLE tutorials, that uses sdk 11. However when I try to do it in sdk 12.3 it doesn't work, because there are...
Hello,
I am using ble_app_uart code. My first goal is to execute a function when board connects with an android device. Another goal is to disconnect board from an android...
When reading about access_opcode_t struct on its infocenter page it stumbled upon this table i don't understand.
access_opcode_t is defined as:
Data Fields
-------...
I'm employing 51822AA.
I need to debug firmware for this chip line by line. Like environment of ARM9 with Lauterbach TRACE32 through JTAG.
Is line debugging possible...
From application point of view, when should I use UICR and when should I use Flash storage? I have studied the documentation and the functionality seems very similar. The...
Hi everyone,
I trying to make a flash jump on Nrf51822 in my project. there are 2 programs(program A and program B) below. i am working on to make program A jump to program...
Hi everyone,
I'm new with nrf52832, and I need to measure elapsed time in microsecond between rising edges of 12 different Gpios. I have 12 piezoelectric sensors filtered...
Hi,
I have used nRF52840-PDK.
And I want to test profile and protocol with PTS.
I succeeded in GATT-based service test and GATT test with PTS.
But when I try to L2CAP...
