hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
In my application, using BMD301 i have made one custom PCB. I am using SDK 12.0.0. In my PCB I have not used all the four LEDs. I have assigned p0.19 to the BSP_LED_0...
I'm using SDK 12.2, and nRF Connect on a Windows machine. I started with the ble_uart example.
I need to send data in my advertising packets. In advertising_init() I initialize...
This is referring to running a peripheral device on the PCA10028 eval board.
Let's say I have a connection interval of 100 ms, and a slave latency of 5.
So the BT stack...
Hello, I am using an nrf51822 but have no success in advertising.
I tried so far to load the ble_app_template from the peripheral examples where I' ve only changed
#define...
Hi,
I am looking for a BT module that can connect to both a BT Jabra audio headphones in addition to a BT HR chest strap with 2 live connections simultaneous.
Do I have...
I understand part of ram is used by the softdevice, but I see different addresses are used in different examples that use the same softdevice, namely S132. For example,
...
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but...
Hi,
I need 6 PWM channels for a BLE project. Is there any solution to add 2 other pwm channels to nRF51822? If not, Which other Nordic ICs might be helpful instead?
Thank...
Hello,
I am using SDK 12.01 with softdevice (BLE application) and I want to write large data over flash. I am stuck with various issues.
When I try to write the data...
Hi,
I am having hard times to make SAADC working on DK-52, SDK13, S132. I need to perform a voltage measurement on command received from a connected device.
AIN pin...
Hi All
I am looking for the way to send and receive the string between nrf52 and mobile app.
what are the possible ways to do with minimum power consumption.
main concern...
Hi,
I've allready read a lot about using a static passkey on the DevZone and I have tried tons of things, but I just can't get it to work.
What I want is to connect...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi, I am playing with the SDK13 examples, UART (w/o softdevice). I use gnu gcc. The example runs and when I type q or Q the code goes to the printf(" \r\nExit!\r\n") as designed...
