I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
This is referring to running a peripheral device on the PCA10028 eval board.
Let's say I have a connection interval of 100 ms, and a slave latency of 5.
So the BT stack...
Hello, I am using an nrf51822 but have no success in advertising.
I tried so far to load the ble_app_template from the peripheral examples where I' ve only changed
#define...
Hi,
I am looking for a BT module that can connect to both a BT Jabra audio headphones in addition to a BT HR chest strap with 2 live connections simultaneous.
Do I have...
I understand part of ram is used by the softdevice, but I see different addresses are used in different examples that use the same softdevice, namely S132. For example,
...
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but...
Hi,
I need 6 PWM channels for a BLE project. Is there any solution to add 2 other pwm channels to nRF51822? If not, Which other Nordic ICs might be helpful instead?
Thank...
Hello,
I am using SDK 12.01 with softdevice (BLE application) and I want to write large data over flash. I am stuck with various issues.
When I try to write the data...
Hi,
I am having hard times to make SAADC working on DK-52, SDK13, S132. I need to perform a voltage measurement on command received from a connected device.
AIN pin...
Hi All
I am looking for the way to send and receive the string between nrf52 and mobile app.
what are the possible ways to do with minimum power consumption.
main concern...
Hi,
I've allready read a lot about using a static passkey on the DevZone and I have tried tons of things, but I just can't get it to work.
What I want is to connect...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi, I am playing with the SDK13 examples, UART (w/o softdevice). I use gnu gcc. The example runs and when I type q or Q the code goes to the printf(" \r\nExit!\r\n") as designed...
Hi
I read somewhere that when using internel ref for analog measurements the Vin changing does not influences the analog reading. Is that true?
Please, consider the circuit...
Hello,
I am looking through the data sheet for the NRF52 and do not see anything for writing to NVMC.
I see you can erase and configure the NVMC using:
NRF_NVMC ...
