I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Is it possible to enter DFU / OTA from a DWT
i.e if the code crashes, and I can't trigger DFU mode by writing to a characteristic, can the WDT jump straight to the DFU...
I met this issue on some Android devices.
GATT connection is disconnected before before service discovery finished.
The issue is reporeted in following link.
github.com...
Hello, I'm using an android device to set cccd, it worked when I was running the project on nrf514xx @s110, it no longer does on nrf52840 S140, so now I wanna make sure the...
I have reformatted the code I had added earlier.
Following is the sequence of code
uart_debug_init();
gap_params_init();
services_init();
advertising_init();
conn_params_init...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
Hi,
I have the Nordic Thingy:52 (PCA20020 1.0.0 2017.19). It worked well until I downloaded new version of firmware 1.1.0 and updated Thingy. After that I didn't see advertising...
I want to use the UICR customer registers to store MAC/serialization information for my devices. It looks like the UICR customer section would be great, and the product spec...
I want to use whitelist in Central (nrf51822,SDK12),but I don't know which function to add the MAC address.
These three functions：
peer_list_get(pm_peer_id_t * p_peers...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
Hi,
we are trying to disable 2 of 3 advertising channels on nRF52832 SoC with the softdevice S132 (1.0.0-3.alpha) installed. The example project ble_app_beacon works well...
hi
I am using ESB_DPL protocol between 51822 and 24LE1, and i used the sdk 12.2 examples/proprietary_rf/esb_ptx.
In my case, 51822 sent some packages with PTX mode,...
Hi,
I am interested to hear if anybody knows if it's possible to use 6LoWPAN on an iOS device together with nRF52832 ? I tried searching online but have not got any hits...
