Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I am using
PCA10040
SDK 15.3.0
Keil IDE
The soft device is S112
JLinkRTTViewer for debug
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart\pca10040e...
hi,
I use nrf5_SDK_for_Mesh_v4.0.0_src and pca10040 borad.
examples/dfu is successful.
But there was an error after the merge.
C:\Python27\Scripts>nrfutil dfu serial...
I setup my adc in continuous mode with sampling rate set to 200ksps, when I trigger NRF_SAADC_TASK_START, I am not getting data; unless I trigger NRF_SAADC_TASK_SAMPLE and...
I am using DSK 15.3, SES 4.30 with SD 132. The base example I am using is the ble_app_uart_c and I am adding the PWM function to drive a simple piezo buzzer.
The pwm_library...
I am looking for a way to interface with the onboard Bluetooth on the Thingy 91 as well. None of the examples (Peripheral NUS, Central NUS) etc currently work with Nrf52840_pca20035...
We have a need to verify an secp128r1 ECDSA signature. I see that this is not one of the curves supported by the CC310, but I'm looking into creating the CRYS_ECPKI_Domain_t...
The documentation says "This module is ONLY for debugging purposes and must never be used in final product". I know in an ideal world all possible errors are handled and device...
Hello, we are developing a system that will include an nRF52832 in peripheral mode, that will be connected to from a maintenance App (or something) on a mobile phone,and will...
Hi support team,
I'm using sdk 15.0 and softdevice s140_nrf52_6.1.0 and nrf52840.
My application has strict requirements on power consumption, so I have to set advertising...
It seems like this should be a simple thing, but I can't find an example of it, and nothing I've read here seems to help.
I want my app to come up in general advertising...
I'm working with Fantel's adaptation of the nrf52840 (EV-BT840F). I have gotten the GFX example working with Adafruit's ILI9341 in SPI mode, however I am having a problem...
Hi,
How do we detect network detach in nRF9160 in a general way?
We use lte_lc to connect which blocks until we have connect/attached to the network. But how does lte_lc...
Hi,
I have a little program that is built on top of the USB CDC ACM example. This little program waits for an SPI event, when the event arrives, it reads the SPI peripheral...
Hi,
For my project I use a ble central and a ble peripheral.
I have to send data from the peripheral to the central and i use hvx indication to do that.
I have two charactics...
