I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
I am trying to retain the data on the board when it is transferred from my computer to the board through uart and once it is on the board through bluetooth to phone. Text...
I am now facing the following issues: https://devzone.nordicsemi.com/f/nordic-q-a/55975/about-reset-during-advertising
I call "sd_app_evt_wait" and go to sleep. Even when...
Hello Nordic Team,
I am creating application to connect with specific device using Name filter,
control is going to nrf_ble_scan_connect_with_target , where "sd_ble_gap_connect...
HI,
The code number for this softdevice version is 0x98. You can find the softdevice code number by typing nrfutil pkg generate --help
But the command only list upto...
Good morning; I am from Argentina, working in a Big Data Project using NoSQL and SQL tools. In fact, I deployed a architecture using Elasticsearch mixing ML, prediction, KPI...
Hello,
about two years ago we have made a Device basked on SDK 13 with S132 4.0.2 on it.
Now we had to build a newer version for our application and for this we have taken...
Hey.
I have a code for processor nrf51422 which compiles using a makefile. However, I decided to import it into a segger - with which I have no experience. For this I used...
Hi ,
I am just unable to find the FW ID for SD v7.0.1 anywhere.
I am using SDK 16.0.0 and SD 7.0.1 and would like to create a DFU package. Any of you know what is the...
Hi there,
I am trying to transmit data with high MTUs via pc-ble-driver-py. The data is sent from an nrf52840 with own firmware.
After the bug in nrfutil was fixed,...
Hi,
im trying to turn on LEDs on my custom nRF52 board. Im using LEDs on 13,14,15 pins. I config pins in pca10040.h to my LED pins, but they dont work. Also if i try to...
I am trying to set up multiple ble diagnostic type services for different sensor devices, from a single nrf52840. The services share a common base id and some have the same...
hi! I'm trying to use the following to configure the GPIOs in nRF52DK for the LED blinky.
nrf_gpio_cfg_output(pin_number)
But I'm not sure what number should I use for...
