Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hello,
I want to transfer data from nRF52840DK to nRF9160DK using SPI. I want to use nRF52840DK as master which will transfer the data and nRF9160DK as slave which will...
Hello,
What happens with the LPN firmware if it currently has an IV index of 0 and loses power for an extended period of time. When it gets power, the network that it is...
Dear All,
I am using the example UART in Peripherals
I can send data easily but have problem in receiving data. When I try to receive data the UART Fifo Event handler...
I looked through the example projects provided in the nRF5 SDK for Mesh, and the only models ever used are generic on/off or generic level. Do you guys have an example which...
Hi,
Sorry for the seemingly simple question. I'm using the nRF52832 chip and I have a 4xdip switch connected to P26, P27, P09/NFC1 and P10/NFC2. I can successfully read...
Hello,
I recently updated the asset tracker on my thingy 91 with the lastet available pre build firmware (2019-11-29_d3130d77) using MCUBoot.
Since my Thingy91 is only...
I started with the mqtt_simple example.
I added:
#CONFIG_MQTT_PASSWORD="pass" #CONFIG_MQTT_USERNAME="David"
to the prj.conf file. Relaunched the project which rebuild...
As a matter of fact that there is no special EEPROM in nrf52832 , the user data which need to be stored in nrf52832 should be written into the flash of nrf52832 . The SDK...
When debuging nrf52832 , the code can be flashed into the flash through JTAG . However , I need to reprogramme the nrf52832 through UART interface . It seems that there is...
Hello.. I use RNF52840 Dongle. I compiled the blink example with VS code and I programmed with nRF Connect tool.
now I can't connect the USB device. I read that I had to...
Hello,
I am currently aiming to create an application for the nRF52-DK using the nRF5 SDK and Segger Embedded Studio as my IDE.
Due to the SDK itself being extremely extensive...
Hello ,
I have been trying the Zigbee CLI light example.
And I modifed the main.c file to have the network saved "ZB_FALSE" and then flashed the updated hex file to 52840...
Hi we are having issues with gpiote interrupt. We would like to do some spi read when drdy gpio becomes high to low. I have done above configuration for the same.
We are...
I have a problem collating model publish events arriving at two different nodes in my mesh.
My application is an array of sensors publishing through generic on off and generic...
Hi,
I have a custom board running NUS peripheral which uses the nRF52832 and a NUS central which is running on a nRF52 DK. I modified the ble_app_hrs_freertos example to...
