Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
HI,
I am trying to Port the BLE BEACON source code of PCA 20006 to PCA 10028 EK.
I have changed the IROM settings.
I have initialized the soft device handler to NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I am trying to understand how can I have a running counter based on the low power 32.768 KHz oscilator that does not trigger any timeout interrupts (I am using the soft...
Hello,
I have a nRF52 to nRF52 connection. I want to secure it (auth and if possible encryption) with a pre shared key. What are the points that I have to modify please...
NRF52,S132 soft device,
I am trying to toggle GPIO 10 (NFC pins Enabled as GPIO)in a 1us Timer, But its not happening , What may be the issue? Am using Timer 4. What is the...
I have programmed nrf51-dk with an example code available at mbed platform,everything works fine except that the ble is visible even if we open bluetooth menu.It is scanned...
Hi,
I'm developing something with NFC / BLE handover - it is currently working fine, NFC tag is read by a phone, nrf52 starts advertising and phone then connects to it over...
Hello,
I'm remaking an nrf52 project in Keil and ran into an issue when it came to compiling. All of the errors outputted have came from bsp.c, mostly stating that a few...
Hi,
We will use nRF52 along with small 8bit micro and UART connection. The MCU cannot support standard baudrate 115200, and we will need to implement non-standard speed...
I am using the Johanson balun ( www.johansontechnology.com/.../Johanson_nRF8001_App_Note_v2.pdf) to interface the differential input of the nRF8001. The PCB manufacture I...
Hello,
I am using the following function call to set up PWM:
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(5000L, BSP_LED_0, BSP_LED_1);
However, the compiler...
Hello,
I designed a board with a nrf51822 on it. My problem now is, that this chip needs far too much current (with no firmware on it) when I apply the 3V3 power to it. I...
I have been working on a project that involves two nrf51 dev boards, one is acting as a central and the other is acting as a peripheral, and I have been encountering a problem...
