Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I played around with the UART demo on the nRF52-DK and the belonging Android apps nRF UART v2.0, nRF Connect and nRF Toolbox. On PC side I used a serial console...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 boarde and s210 soft device. My firmware makes use of sd_power_system_off(). If I have an update...
Hi guys
I'm trying to load the ble_app_beacon project on a custom board. I am able to flash the softdevice and the application, but the chip is not advertising. So, I started...
I've got the experimental ble blinky example project on an NRF52 PCA10040 working fine with an added custom characteristic. I can connect, discover and read/write characteristics...
Hi
I've implemented support for the FStorage and the FDS in our application. In some cases it happens, that the function "fds_stat" does not return.
The reason can be...
Hi,
Is it possible to reconfigure NFC pins to be GPIO inputs (and vice-versa) without any kind of reset? It seemed like some kind of soft reset was required when I looked...
I am trying to run the multilink central gcc example with s120 v2.1 on a nRF51822 CEAAD20 device. Unfortunately, SOFTDEVICE_HANDLER_INIT call causes a hard fault. The linker...
I'm trying to pass a string longer than 15 characters to NRFJPROG_rtt_write (it's 17 characters, including null-termination), but the data_written parameter is set to 15 after...
Hello everyone,
I am wondering that, can i find auto-connect feature on nrf chips? Firstly, i should match chip & device i know but after that can they match?
Second...
FWLog (1)_formattedByTC.txt Hi,
I am sending data to one of the characteristics from nRF51 to the App(the problem happens in both iOS and Android).
This is what I am observing...
Is there any documentation on the advertising state machine ? This post :
devzone.nordicsemi.com/.../
mentions the state machine and how it progresses from fast, to...
Hi all,
I want to update my connection parameter as follow:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) //400 /**< Minimum acceptable connection interval...
Hi,
I'm doing a project using the Evalution kit.
I don't know why, but I can't go under 350 uA current comsumption in system on.
I did clear all pins,i did NRF_SPI0-...
HI:
i use SPI is ok when i set frequency = NRF_DRV_SPI_FREQ_1M,but SPI will work abnormal when i set frequency = NRF_DRV_SPI_FREQ_500K/NRF_DRV_SPI_FREQ_250K/NRF_DRV_SPI_FREQ_125K...