Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am new to Nordic Evaluation Kit.
I am working in Nordic nrf51822 (PCA10001) Evaluation board.
Following are my setup.
OS : Ubuntu 14.04 64 bit.
SDK : nRF5_SDK_11...
Hi all,
I need to know the RSSI Value (distance) between my nRF 51 DK and my connected device (iOS Device). I made these code changes:
switch (p_ble_evt->header.evt_id...
Hello!
I've been using RTT viewer to view some data in my nRF52832. Everything works fine but I am unable to clear the RTT viewer terminal screen.
As it is in the manual...
Hi,
I am trying to get the experimental NFC example "HR with pairing over NFC" to work.
I can read the tag correctly with an android phone : the NDEF message is correct...
Dear All：
My NRF24L01+ use Dynamic PayLoad,What register need configure NRF51822?
NRF24L01+ Configuration as follow:
SPI_RW_Reg(WRITE_REG + DYNPD, 0x01);//Enable...
Hi,
I've been using the ble_app_uart example as a template for our use case. It is a good starting point. We don't actually need UART functionality, and we've assigned...
Hi,
during programming, we receive error as in this question . The hex files do not overlap.
It seems to happen only when the board has already been programmed before...
Hi,
I have an application that requires watchdog to run continuously. And from application I have code that jumps to the bootloader without device resetting using bootloader_util_app_start...
Hi,
Side effect of adding a LFCLK of 32.768khz with 90k ohm ESR oscillator? where as data sheet recommends Max value of 80kohm.
Side effect of adding lower drive level...
Hi everyone,
I activated softdevice writing protection with nRFGoStudio (i.e. so that the softdevice can not be overriden). How can I deactivate that again so that I can...
Just to make sure: Will The spi_master_send_recv return when it is done writing and reading, or do you have to have some event wait functionality listening to SPI_MASTER_EVT_TRANSFER_COMPLETED...
I was playing around with the gpiote example under exaples/peripheral/gpiote. The example uses a timer, ppi, and gpiote to blink an led. By default, the app uses Timer 0 and...
Hello.
How to write custom firmware updater, which:
Takes new firmware from other device on SPI or I2C bus.
Writes it to flash ("bank1" at 0x1B000, or...
Hi;
I'm studying on SPI communication at nRF51822 (not DK) but i could not find the pins for spi communication, i read at somewhere SPI is only used at DK(developer kits...
