Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
hello.
I want use I2C program.
so, I used twi_master_using_app_twi example.
SDA is output only 1byte(0x21).
I need to output a continuous 5byte.
Where do I need to modify...
Although the login form in the right side-bar works, the on in the main page does not. To reproduce:
Log out,
Click on 'Sign in' on the side bar
It should take...
Hi,
I am trying to use PPI for generating a output of lo to hi when NRF_RADIO->EVENTS_READY occurs.I want to generate on the same pin hi to lo when NRF_RADIO->EVENTS_END...
There are a couple of threads in the Developer Zone which mention backwards compatibility issues for nRF51822 BLE with DFU. Some of these are focussed around MCP (Master Control...
Hi !
I would like to use FFT with the nrf52. There are some FFT functions in the arm_math.h, but the linker fail :
1> Compiling main.c
1> Linking nrf52832_xxaa.elf...
Hi, in older SDK there seemed to be a simple way to redirect stdout (simple_uart.h), but in SDK 11 I cannot find these functions. What is the recommended/minimal way to redirect...
I use the nrf51822qfaa,s110 v8.00,SDK V10.0.
I use PWM module with a piezo buzzer.
Now I need change the buzzer frequency,
How can I change the PWM frequency?
for example...
I started looking at the alert notification example. I just can't see how people understand the complex state sequences the peripheral (or central for that matter) go through...
I am using em::blocks and arm gcc with ble nano from readbear labs.
I built the template example but it is not working.
The output hex is the same as if i had built it with...
Hi, I am about to purchase PCA10040 V1.1.0.
I heard that one has the latest chip revision nRF52. ( ref. link )
I'm very excited to start with the new feature in nRF52;...
I have a peripheral and a central.I set my peripheral which have the function of static Pin,for example: When I use cellphone to connect to my peripheral , the cellphone must...
Hi all,
I am trying to read and write in ble central and peripheral code with softdevice s130. Here i can able to connect to particular ble device with unique ble device...
When trying to setup the gcc toolchain with Eclipse Luna IDE, I ran into the problem when I can't set a break point when debugging with the GNU ARM J-Link Debugging Support...
