Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
Hi all, hope this is the right place. I'm developing a small breakout board to test/program the NRF52805; this board will eventually be expanded to include a pressure sensor...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello.
After some great struggles, we've managed to enable WiFi and encrypted socket + TLS connection to google.com and various websites.
Since then, we've been looking...
In Electrical specification Table 1 (current consumption in forced High Power mode) lists a typical value of 7.2 mA , just want to confirmed this is correct and not a typo...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
I'm trying to regularly change some advertising parameters ( ble_gap_adv_params_t.type ). The only way i can see to do so, is by stopping and starting advertising.
However...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile（PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
I am working on S140 on nRF25840. I am using the ble_app_beacon sample.
I want to set the advertising interval smaller than 100ms while using non-connectable mode. But the...
I am developing a product where I need to read a signal from an SPI ADC and send remotely to a receiver. This will be powered of a coin cell.
I see that the NRF51422 is low...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
