Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi. I'm trying to flash Secure DFU bootloader together with my application. I tried to flash bootloader and then main application, but the device stays in bootloader instead...
ppi.zip Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. Even after allocating the access address of Bluetooth on line 196 as set_address0...
Hi there,
I am trying to measure environment below 0 C but the app reboots and refuse to connect with thingy52 at lower temperatures. Do I have to set up anything else...
hi ,
I have a question about rtc.In my project ,I use rtc1 for app timer and rct0 for low_power_pwm.The problem is that I dont't have any idear to enable rtc0 instead of...
hello:
i meet some trouble,i can find the service,then appear error "BLE_GATT_STATUS:10a".
#define BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND 0x010A /**< ATT Error: Used...
Hi,
I am trying to use the nRF51DK (PCA10028 v.1.2.2).
I cannot get Windows 7 to recognize it via USB reliably. I have JLink v6.16a installed and when I plug in the board...
I have variable values coming out of a terminal at all the time. I using this command:
void in_pin_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
...
Hi All,
I am developing a ble applications and am unable to get pins 9 or 10 to work as gpio. I understand that this is because, by default they are used by the NFC.
...
How do I limit the number of peers that are stored in the peer manager? I don't see a configuration variable. I don't know the addresses of peers before hand, so I don't think...
Currently, I am trying to develop nrf51822 ( MDBT40 ) using Nordic SDK v12 (S130). The programmer I used is DAPLink from RedBear .
I am wondering how to make program to...
Working with the NUS, I sometimes see ble_conn_params_on_ble_evt getting called in a way that will cause the data being passed through NUS to stop. Not all the time, just...
Thats the problem.
On Windows7, 64 bit, with the Bluetooth Stack from the USB BLE-Stick happens the following:
Windows (master) initiates the connection, sends a security...
