Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Master control Panel.exe 3.10.0.14
winxp sp3
.net framework v4.0
The day before yesterday it's OK, but this morning MCP won't start. The windows event info shows:
...
Hi
I'm looking for a functional example based on Freertos and nrf52 on SDK11 and SD132. I'm having problems (hard fault) and I've been looking for this example but with...
Hi There
I see there is a Proximity App - is this available for downloading like the beacon App ? for use in xcode ?
Also, in the demo, there was a bluetooth unit that...
I use a android phone as central(Master) and use a nrf51822 as a peripheral(Slave).
The peripheral can send the "L2CAP Connection Parameter Update Request" to change the...
Hi
I have a BLE nRF51822xxAA project created with Keil 5.15, SD 100 ver 802 and Family Pack 803.
I made a new configuration in a new machine with Keil 5.2 and I am getting...
I want to create my own PCB which can communicate with the following Transmitter:
www.hobbyking.com/.../_ 43854__Turnigy_5X_5Ch_Mini_Transmitter_and_Receiver_Mode_2 .html...
Hi! I work with a smart Beacon Kit nrf51822 rev1.0.0, s110 and I have visualised my current consumption. What I expected to see is that my beacon could send in one time all...
We are preparing a project where several mobile phones
with Android OS in peripheral role will be connected continuously to
one nrf51822 with S130. Communication must be...
On nrf51 I was using:
pre flash: w4 4001e504 1
erase all: w4 4001e504 2\n w4 4001e50c 1\n sleep 100
pin reset: w4 40000544 1
Is it still the same for nrf52...
[Edited title]
My application on a PCA10028 board is attempting to send a BLE advertisement using sd_ble_gap_adv_data_set() by going through ble_advdata_set in ble_advdata...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
is there something like a makefile for nrf52 out there?
I want to use eclipse and gcc in osx. It worked great for nrf512 but nrf52 has other addresses and maybe...
Hello all,
Lets assume that central bonded with nRF51822 peripheral and than disconnected. If bond is saved on peripheral- ok, cental send BLE_GAP_EVT_SEC_INFO_REQUEST...
When i try to do an update with Nrfutils Under android i get a REMOTE_DFU_OPERATION_FAILED since i added signing.
I created my pem file key with nrfutil.exe keys
i copied...
Hi
I'm trying to get working a project by using S132 v3 alpha. I'm stuck at function sd_ble_enable. This function should return the minimum RAM memoy would need the SD...
