Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I'm developing with an NRF52832, using NCS v2.6.1/Zephyr 3.5.99
My custom hardware has three NXP PCA9538 GPIO expanders on it, to allow me to control various address and...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hello,
is it possible to get the schedule that is used internally to communicate with connected BLE devices? I have a bunch of data that I want to send to connected nodes...
Hello everybody...
I am new to nordic development tools. I wanted to develop a ble application on the nRF51822 development kit. I am struggling to figure out how to set up...
Hi All,
I am using s110 v7 soft device , and SDK: 6.1.
I have implemented static passkey based pairing.
I would like to terminate the connection if central unable to sends...
Hi I am using the RBC mesh " github.com/.../nRF51-ble-bcast-mesh" , sd_110_7.1 and sdk_6.2
The rbc mesh is using timer0 as well as the softdevice. I removed the app timers...
Hi all,
we are performing some transmitter spectrum measurements using your nRFGo (PCA10005) board and an Aaronia HF-60105 spectrum analyzer.
The SMA connector of nRFGo...
i have nrf518822 device..i downloaded s130 soft-device from nordic website..i have installed keil 5.0 and nrf go stuidio....now tell me how to flash soft device and application...
if i use s130 soft device will it do simultaneous master/slave role.....
c1=central 1,c/p=centarl/peripheral,p1=peripheral..
assume c/p made a connection with p1 and it...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
I have an ANT device, that on a button press, it must wake up, connect to an ANT channel, and send a...
Hi all,
I am trying to connect a tablette (s110 peripheral role) to 5 S120 centrals simultaneously.
I am using nrf51822, sdk6.1, s110 v7.0, s120 v1.0.1 .
Is this possible...
So I've seen all similar issues people had where their program stuck on sd_softdevice_enable() due to the fact that ran on custom boards which didn't have external oscillators...
This are the contents of disassembly window on all optimisation levels. Program is stuck switching between two operations:
MOVS r0, r0
DCD 0xFFFFFFFF
I'm running...
We're moving our design from nRF51822 to nRF51422.
What's the difference between these IC from the point of view of PCB layout and antenna design? Are they interchangeable...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi,
Are there any available examples of Makefiles with JLink command integrated?
Example: "make flash" to flash the image or "make flash-softdevice" to flash the softdevice...
