Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
Hi Team,
Iam doing project called automation of light using BLE technology.
Here Iam using sdk 12.1.0(ble_app_hrs_c) example for scanning or receiving and i flashed...
I have a small problem with my bootloader + application on NRF52832. I'm using SDK 12.2.0 with S132 v3.0.0.
When the device loses power, and power is then re-applied, the...
I'm using nRF52 + s132v2.0.0 + SDK11.0.0. I want to be able to update to s132v4.0.2 (or so) + SDK13.0.0 via DFU. I'm planning on modifying the bootloader start address to...
I'm using nRF52 + SDK11.0.0 + s132 and have a couple of questions on DFU.
I want to use a CMSIS-DAP programmer + OpenOCD to upload the bootloader (or BL+SD+APP+setting...
Hi,
I am using a nRF51822 board and I wanted to know if the LC filter is necessary if I don't need to use any analog entrance or exit. I just need the BLE and a digital...
Hello,
I was trying to load code in pca10028 and I started getting error as "No cortex M Sw device found".
It was working properly but later it started showing me this error...
Dear Nordicers,
I have an application where node based on s132 sofddevice 4.0.2 has multiple connections as a peripheral and as a central. The case is about non overlapping...
I have an NRF52832 DK [PCA10040, V1.1.0]. It used to do programming with it, but now it suddenly stop detecting as "JLink" in Windows, Linux and Mac. Now when I connect it...
Hi, I use the twi_master_using_app_twi_pca10040 (SDK 12.1) to test the TLC59116 LED module .
By changing the example project's code by referring the GitHub code, I have...
Hello the Nordic Team,
I come here after a lot of research and testing and do not understand what is going on in my program. (is it Embedded or iPhone nRF Toolbox side...
hi,
I follow the pwm routine, 51822 can work and output pwm, when I want to change the frequency of pwm encountered a problem, the program reset.
I use the method when i...
Hi,
I'm using Nrf51822 to implement a RTC(200ms tick)
I connect a external 16MHz crystal to the MCU.
I use the S110 softdevice with BLE function enabled, so it's in ble_stack_init...
Hey. Has anybody played with autocomplete for command line interface.
I like it alot and it is very helpfull. Now a autocomplete would be cool!
Here is what comes to mind...
How to setup a nRFDK52 as a central and nRF bluetooth kit as peripheral. Should I use nRF go studio? Do i need to load the soft device first before loading the app? What is...
I want to store two floats and one 8 character string in fstorage.
I solved it by using 4 uint32 types stored in flash, I got it working in the ble_app_template example...
