Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
I am trying to create a partition on my external flash using littlefs
Here is the line that is returning me an error
FS_LITTLEFS_DECLARE_DEFAULT_CONFIG ( storage ...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
Hi Nordic team,
I print logs at each function in ble_bas.c. I used the App of nRF connect to test BAS. I can see on_connect, on_disconnect and on_write at enabling/disabling...
Hi,
The spec(nRF52832_PS_v1.3.pdf) said the peak current of TX/RX is 5.3/5.4 mA.
However, I use the PCA10040 board and the ble_app_template(SDK 12.2.0) sample code...
Hi,
I can see that Apple states that iPhone 7 supports LE Data Packet Length Extension forums.developer.apple.com/.../73168 . Anyone know if the packets per event and the...
Hi,
I have NRF51822 module with custom carrier board.
I trying the experimental ble app blinky (S130) with PCA10040 (master cenrtal board S132) works fine.
When trying...
Hello,
I test new SDK 13 and i have a problem. I don't success to debug bootloader. When i open .out file into debugger, sources are not complete (main is missing) so i...
Hello,
Is that possible to use a mbed application with SDK bootloader ? If yes, with signing too (if i sign application after generation) ?
How to set memory mapping...
I am trying to program an nRF52832 on an nRF52DK via the Debug in port (P18).
I am driving it with an STM32L073.
Should I put the nRF52832 into reset via the Debug in...
hai
in my application i am using nrf51822 . i have connected some sensors with the mcu. and i am collecting values from the sensors and this values are updated to the service...
In our code we use NV storage for system settings and calibration data.
I'm trying to understand when to open/close files and which structs to keep bwtween reads/writes...
Hello,
I'm using nrf51822/sd130/sdk12.1.0 and SOFTDEVICE_PRESENT defined.
But, I didn't enable softdevice.
I want to realize power save mode.
when I use __WFE...
hello there, i am using sdk11, i am using uart example. i am using nrf51 dk
SEGGER_RTT_WriteString is working. but
SEGGER_RTT_printf is not working. main.c
i have seen...
hello everybody,
i've downloaded the firmware files of nRF51822 beacon, but i couldn't find the source code. Does anybody know where i could find the source code of nrf51822...
