Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 26 bytes, I have configured the port to 1MBoudRate. Once I prepare the frame...
Hey guys,
I followed this guide and successfully synchronized the timers from two devices(nRF52 DK). But if I let these two synchronized devices keep running all the time...
Hi,
As stated here :
After manually starting the HFCLK
crystal it will be enabled even though
there are no peripherals requesting
the HFCLK. When no peripherals...
Hi,
I have my 2 nRF51 running with S130 v2.0.1, one is the central and the other peripheral.
I am transmitting audio data between both and want to reduce the current consumption...
Being a person with a poor name memory, I am really frustrated with the nRF SDK's naming conventions. For example, let's take a function
bsp_btn_ble_on_ble_evt()
Is...
We are using nrF52 series in combination with v3.0.0 of the S132 SoftDevice stack. And I want to understand if we have to go through any of the qualification certification...
Hi,
i got a random disconnect and cant find the cause.
I found this post devzone.nordicsemi.com/.../ and tried to folow the procedure.
I have set up breakpoints wherever...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control the onboard led that uses the methods LEDS_ON and...
I am using the nrf52832 with its Development kit to transmit trough UART to the PC a frame with 20 bytes, I have configured the port to 1MBoudRate. I have enable the flow...
I spent some time trying to work out why generating a private/public keypair in my application with the ECC module was failing due to an 'internal error' and had to eventually...
Hi,
In 868 Mhz band NRF905 supports frequencies 862.8Mhz, 868.2Mhz, 868.4Mhz and 868.8Mhz. The datasheet shows mapping of those frequencies to CH_NO.
In India only 865Mhz...
Hi,
I am currently working with two nrf52 boards in a serialized configuration.
I wanted to add the PA and LNA pin toogle on the connectivity chip.
As the gpio can't...
sorry, i tried "Getting started with the nRF5 development kit" tuturial about 3 hour.
but still not working for me.
stock at begining.
I downloaded nRF5 SDK 11
and...
Hello,
We are using nRF52 in serialization mode.
In the nRF52 connectivity chip side, we are using the example 'ble_central_and_peripheral'.
In the application chip,...
