I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
hi there!
i'm struggling with the problem about using i2c with IoT SDK.
my project is about transferring sensor data (i2c) through ipv6 over ble , so i used the IoT softdevice...
I'm considering purchasing a nrf51 sniffer USB dongle. I believe I can use this to sniff beacon packets and with wireshark view the packet internals, data, channel number...
Hi
I tried to flash the softdevice with nrfprog, but it does not work. Even with nRFgoStudio it does not work.But with IAR I can program an example of the SDK (without...
Hello, all
I have a problem with ble data exchanging.
I have programmed an application which controls servo motors through phone application.
At the connection, ble...
Hi,
I am trying to use the SAADC to periodically sample an input from AIN0 and send the resultant data over a BLE link to a phone. Going through the forums I saw that the...
Hi,
I am trying to debug the blinky example project on the nRF52 development kit.
I have followed the following tutorial: devzone.nordicsemi.com/.../
Building and flashing...
I'm in the process of designing a circuit that requires Bluetooth. So instead of having a separate chip for Bluetooth and processing, I decided to use a Nordic Semiconductor...
Classic C documentation issue. Are the values that are passed by pointer (p_peer_address and p_whitelist) to sd_ble_gap_adv_start() copied into that function, or do they need...
I'm trying to read the 32-bit value of TIMER1, but it seems the value I read is always 16-bit value. When I debug the value is never above 0xFFFF.
snippet from nrf_drv_config...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
