Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi guys I'm sending data from an nexys 4 fpga through an spi to my nRF51 (pca10028) I have the fpga set as the master and I'm able to read data sent to the nRF51 through my...
Hi.
I'm using nrf52 as slave for another device. I'm reading test string from the nrf buffer and I can see extra zero (rest of the content is then offset by one -> corruption...
Hi, i know this question has been ask before but, i was reading and readind and i could find a way to do it. I got the theory but when i'm going to implement it in my code...
Hi there,
i cannot get the hrs_c example to connect to a heartbelt.
The heart belt is found and a connection is established:
[APPL]: >> DM_EVT_DISCONNECTION
[APPL...
Hi
I am working on nrf52 using BMD300 RIGADO board.I am trying to run BLE UART example of nrf SDK 11.0.0.But while I am running the code I am getting errors as
: struct...
In Nordic infocenter/nRF5 SDK v11.0.0/Examples/Bluetooth low energy examples/BLE Central & Peripheral/, I found a example project which name is "Experimental: BLE LE Secure...
BLE is first initialised in my code, then SPI is initialised. If no SPI transfers are to be executed in the code, the code compiles, runs correctly and BLE functions correctly...
I have a very simple program that generates a 50% duty cycle clock using the NRF_PWM0 on the new nRF52 device. Unfortunately, my Tektronix 1GHz oscilloscope doesn't lock to...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Is there a way for firmware running on the nRF52 to detect the presence of a SEGGER (or other) SWD capable device? I've looked through all the nRF registers but couldn't find...
Hi all
Our application, built on the NRF51822 Rev. 3 and the SoftDevice S130 V1.0.0, uses the UART0 with 115'200 baud, 8N1, to communicate with another controller/PC. Hardware...
Hi, In my project I want to read data from i2c and update in advertising data and the board need to advertise without time out (i.e 24x7) for these I take advertising timeout...
Hi,
I am new to the BLE profiles. I am have to send the TMP007 temperature sensor values to mobile APP using BLE HTS profile. for this I am using sample example of nrf52...