Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hello Nordic Support Team,
I’m developing a Zigbee-based light switch using a Sleepy End Device (SED) configuration with ZBOSS. I've encountered a critical issue related...
Our IC nRf51822 has an identifier "QF AA CO" (IC rev 1) The document "nRF51 Series Compatibility Matrix", Table 4, shows the maximum version of the SDK 5.2.1 and 4.4.2 SD...
Hi guys,
I install V1.6 nRF ToolBox apk in my Android phone, and want to do the DFU operation.
When the device in DFU status, I select the target HEX file but it shows me...
We are configuring the watchdog like this:
// Watchdog
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Run << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Run << WDT_CONFIG_SLEEP_Pos...
So I've got this long characteristic which takes several read operations with offsets to read it completely. Idea is to have it refreshed only after the client has read it...
Hi all,
I've have written a debug version of our application firmware to catch any and all error seen during operating. The most common one I see is NRF_ERROR_BUSY stemming...
Hello,
I am doing some tests with the Heart Rate Service Sample Application for the nRF51822 evaluation board (PCA 10001). Inside the ble_stack_init(), there is this call...
I am trying to bring up a simple program on the IAR tool chain 7.40.1 using an I-Jet debugger using the nRFDK. I have this simple programming running under the Keil code limited...
Hello,
I tried to merge the UART example and the HID keyboard example.
When I pair my phone (android v4.4.4) to my nRF51422 chip (in the phone bluetooth parameters)...
I'm still having a bit of trouble getting my board to receive Heart Rate information from the demo example provided in the 7.2.0 SDK. I've configured the network key correctly...
I am trying to hook up the following accelerometer with my MPU-3050, but I am having trouble reading from the registers. So far I have code that looks like this.
Accelerometer...
Is it possible on the nRF51822 to surface an every from the Soft Device whenever a client attempt a scan (is it SCAN_REQ?)
This is for an iBeacon implementation where I...
I'm doing some work with the nRF51822 smart beacon kit. I tried to do an over the air firmware update of the application, but kept getting dfu invalid state (2) errors after...
We've got an application (not using SD or SDK functions) that locks up the nRF51822 and does not reset even though the watchdog is configured and confirmed to work in all...
The release notes for SD 8.0 note "The default behavior is now that the application can use the CPU while the radio is active".
Does this mean that this code is no longer...
Hi,
I am trying to connect the demo board nrf6929 to my demo nrf51822 (PCA10001).
In nrfready_voice_input_module_user_guide I couldn't find any information about updating...
