Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
I'm trying sending 3 bytes in standard example from nrfgo - but it enters in interrupt with fail - occurs maximum re-transmits case. Project in this folder:
C:\Nordic Semiconductor...
Hello,
I know that Vdd on nRF24L01 module should be on 3.3V power and probably will be burned if get 5V power.... If in any case that happen at some point of experimentation...
Hello!
The company for which I work is migrating from NRF24 to NRF51.
Our protocol relies on ESB and uses payloads of 32 bytes and payloads in ack (also 32 bytes).
...
Hi,
after receiving button event application crashes. I get NRF_ERROR_NOT_FOUND from app_sched_event_get and device stop responding.
What can be the reason?
Thanks...
Hi,
recently I purchased the nRF51822 Beacon Kit. I downloaded the hw files and unfortunately realized that they are altium designer files.
As I'm using Eagle I would like...
Dear All,
I've recently had a problem with interaction with samsung phones (S3, S4, note 2 on 4.3+) using 51822. The connection interval that I have is around 48ms with...
**nRF8001 + STM32 microprocessor + ble_HID_keyboard_template (from Arduino)**
I am now trying to port the ble_HID_keyboard_template from the Arduino:
After the reset...
Hello support team
Have you tested the nRFgo 1.15 x64?
usually x64 installs in Program Files this installs in Program Files (x86) any reason why?
I had to recover my PCA10001...
is there any complete altium designer file including schematic and pcb file for nrf51822 ?? there is only layout file in the website...... if you have it please email the...
Hi
I just updated our project to files from new SDK release 6.1. The normal application is working properly with the new SDK, but i got in trouble with the bootloader parts...
Hi all
I would like to use the s110 softdevice V7 with the nRF51422 which I know is possible. However, I would like to start the work with an example project, but I can...
I want to make a indoor positioning system using bluetooth 4.0. so for this HOST should recieve the RSSI from the devices it is connected to(from RSSI to distance conversion...
Hello,
I am working with the nRF8001 device:
When I try to configure the device as a service data broadcaster and go to the nRF8001 Setup -> Generate Source Files (in...
For improving my data trouchput (both directions, using »Write without response« and »Notification« like e.g. nRF Uart Example do9, I'd performed some tests regarding the...
