I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC RTC.
It function well when connected to EV board...
I see the "Emulated System OFF...
Hi all,
I'm using the nRF51822-EK (PCA10001) and I'm going to develop a bluetooth cadence (and speed) sensor for MTBs.
I desire low power consumption and i though to put...
hiii...
I was working on ble_app_hrs example of sdk-6 using sd7.0.0. I tried to add broadcast feature by sending some hex values, dat was working, but now i want to display...
Hi,
I need to use 2 TWI bus (hardware constraint) so I wish to drive one bus with twi_hw_master.c and an other with twi_sw_master.c.
Each bus have their own GPIO.
...
Hello.
I'm reading the nrf51 Reference Manual.
in MPU section, [ (SWD) will no longer have access to code region 0 or code region 1, as well as no longer being able to...
Hello,
downloading the file nrfgo_sdk_2.3.0_setup.exe causes the virus scanner to report an issue and moving the file into a restricted zone.
Can you help on this...
hi, i made ble app with nRF51822 (s110), sdk 6.1.0
and i put this code after a pstorage_store() function to wait finishing of this function.
uint32_t err_code, count;...
My board is nrf51822.
Simple_uart works fine in uart_example, but once I copy it to my ble project which can work, it stuck.
Part of my code :
advertising_init();
services_init...
Hi all,
Now I'm using the nRF51822 DK and nRF Loader APP do the OTA.I can use the APP to complete the firmware update.However,the device
cann't go back to bootloader mode...
I'm trying to build an application on nrf51422 with s310 SDK ver5.2. My application is working fine with Bluetooth and now I want to add ANT service to it so can anyone please...
We are running OTA DFU bootloader provided in SDK 6.0 on nrf51822. We noticed that when the chip has been on for a while and we quickly power cycle it, the bootloader sometimes...
Thank you for your reply,Nikita
description of my system: Hardware:nrf51822,pca10001 Software:sdk5.20,run the softdevice s120
According to your reminder.i reference...
Hi,
We need to simulate the peripheral through PC, but with current version we cannot use 128-bit UUID which we need.
So the question is are there any plans to release...
Hi,
I want to init all 8 pipes in the host device (gazell protocoll) with a single init byte.
Thats important because i want to send that init byte to the devices with...
Hello,
as I know max number of simultaneous connections for s120 equals to 8. Is it software or hardware limitation?
Is there 'serialization' version of s120 (worked using...
