The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I am working on ble_app_uart_c example provided in SDK12.3.0 with S130. I tried this example on PTR5518 ble chip but suddenly device goes resetted every time.I am printing...
I'm finding rather high power consumption developing freeRTOS on the nRF52. I have it found that it appears Task's are suspending properly on the main BLE thread (copied from...
Setup
I was just looking through the code in the HIDS module in more detail, now that I have built a few demo HIDS apps I want to make sure that I understand the HIDS module...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
Hi
I am using nrf52840 for indoor positioning application based on RSSI. I was wondering if somebody has a tip how to calibrate the nodes before doing the experiment.
Hi,
I'm using sdk12.3.0 ble_app_uart.
My problem is BLE connection.
Sometimes(almost 50%)I tried to connect BLE but fail and I have to connect again.
I don't know...
Hi, I'm contemplating ways to drive a small RGB LED matrix with the nrf52832 in a really space-tight project. Ideally without any external components. I'ts maybe around 40...
Hello,
I need do synchronize the time between two NRF52 devices. One is connected to the other by a custom BLE service. Do you have any ideas how this could be done?
...
I'm trying to integrate buttonless DFU with secure bootloader with bonds with the DFU.
Using SDK 14 with SD 132 v5.0.0.
Using projects: secure_dfu_ble, ble_app_hrs_freertos...
Hello:
When I try to open an example project from nordik, keil doesn't open some files and I get the following error:
"no source": Error: #5: cannot open source input file...
in main() I initialize the timer
// Initialize the clock module
ret = nrf_drv_clock_init();
APP_ERROR_CHECK(ret);
// Request the low-freq clock to start N/A for SoftDevice...
SDK v12, SD130 on 51822.
I init uart through APP_UART_FIFO_INIT, and installed uart_event_handler. UART rx/tx with an external MCU works OK while softdevice running.
...
Hi. I have some nRF51 firmware I'm migrating to the nRF52. It's a peripheral with bunch of vendor specific services, using SDK 13.0.0 and SD 132 v4.0.2.
My code builds...
