Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Q0. What IRQ Priority does BLE Has? and also what IRQ Priority does UART can have?
I'm guessing that from s130's document P65, Exception Model, It says,
Softdevice Timing...
Hello,
I could not set breakpoint in Eclipse. I set CFLAGS to -O0 and -g3 in Makefile
I am using GNU Tools ARM Embedded 6 2017-q1-update and Eclipse Neon3
Below are...
Hi,
is at the moment possible with S110 (nRF51 SDK) to whitelist only SOME of bonded peers? I need to allow connection from one selected central. Selection is made by user...
As a follow up from devzone.nordicsemi.com/.../ , I am now trying to find out if I am getting all of the memory settings put together correctly. When I have them at higher...
I am using nrf51822, 16K RAM, 256K Flash.
From the movie , there is no way to secure my firmware for DFU. Is there any other way to secure my firmware?
Thank you
I know the many differences coming in bt5. Will the programming concepts be the same in the upcoming 5 version? IF my code is working with ble4.1 will it automatically work...
After a bunch of headache I was able to successfully program with the nRF51822 Development Kit without the nRFgo Starter Kit motherboard, here is how I did it.
Hardware...
I'm working on a design that incorporates an nRF52832 along with some sensors and drivers.
Up to this I've been sacrificing power consumption in prototypes by using LDOs...
Hello,
Is it possible to change SPI baud rate whenever we want?
For example:
The initial SPI baud rate is set to 4M. We want to change the baud rate to "2M" to get...
Hi,
This may be stupid, but I can't declare classes in my .h file in keil. I have arduino library for my I2C device, but keil; does not recognize when I declare classes...
I've looked through and tried many examples on getting my SAADC to produce a temperature offset. About a month ago I had the SAADC working really well with a wheatstone bridge...
Hello,
What changes need to be made to the following tutorial to enable basic advertising with the Rigado BMD-300 on a custom board breakout board?
devzone.nordicsemi...
Hi,
I have multiple devices set up in a simultaneous peripheral and central mode that exchange data on connection. As there may be multiple devices around, I want to make...
i download the sample code (\examples\nfc\record_text) to pca10040,it can be detected by NFC reader,the serial number is 5f:46:ac:eb:75:a7:ea,if i want to change this number...
I am working in sdk12.2 nrf52832 . When build and run the project it will work smoothly with ble connectivity... But the problem is it will bond only once when the softdevice...
