Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I want to undestand this. I can't see any examples with it. In the example ble_app_proximity I always received 100% level.
If it possible, can anybody give a ADC config example...
I am working with a Blend Micro Board (Arduino IDE with RBL_nRF8001 sdk), using
Evothings.
Using the RedBearLab Simple control example I can easily connect to the board...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
OpenThread recently merged a DNS client into the main branch. DNS would be extraordinarily useful because my code accesses content behind load-balancing servers with dynamics...
In this example code:
nRF5_SDK_13.0.0_04a0bfd/examples/ble_peripheral/ble_app_proximity/main.c
Where the ADC is configured to read the battery voltage:
nrf_saadc_channel_config_t...
Hi,
I've read a couple of threads in this forum that suggested that the DEVICE_MANAGER_APP_CONTEXT_SIZE value (which should be a multiple of 4) is supposed to be 16 bytes...
We're using the nrf51 with the RFAxis (now Skyworks) 2401C amplifier, which is a fixed gain 20dBm amplifier. The goal is to have a longer range 'beacon' type product and the...
What would be the best BLE Library or Framework for Raspberry-pi to exchange with nordic?
I'm trying to get data from the NRF51's GATT data.
But there are no reference...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
