Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, I'm migrating a project from nrf51 S110 to nrf52840 S140, I encountered an error
"nrf_nvic_state" not found, I solved it by adding app_util_platform.c.
The problem...
Hi,
I am trying to make an empty custom service by following this tutorial from Nordic
devzone.nordicsemi.com/.../ . However I am unable to get the service to show
up...
Hello comunnity,
I am trying to read, write and activite notification from my server using a central device. The problem is when I use more than 2 times, I got an error...
Hi,
Ive been having a problem connecting the phone directly through setings to the nRF51822 chip. I'm doing evertithing in mbed. When i connect the chip via the "nRF Connect...
Hello , i'm trying to implement the OTA DFU function in my custom designed board. I'm using NRF52 series. I started by flashing the flash I uploaded the softdevice132 v2 via...
I am using saadc to periodically sample a voltage (per about 12 seconds). The voltage cannot be shutdown and always is a value neigher zero nor VDD (1.25v, 2.5v, 1.0v, etc...
Hi,
I'm wondering if the DTM mode can be entered over the air interface on nRF bluetooth products, as specified by Core4.2 [Vol2 Part C] 4.7.1 Activation and Deactivation...
Hi,
I am looking for an solution which requires to have an BT dual mode(Smart Ready) SoC. As i require the high data rate of 2.1 and also require support of BLE 4.0.
...
HI ,
I need to interface particle measurement sensor with nrf52832. I am using S132 softdevice and SDK 11.0 for my application. I need to send commands to sensor to take...
Hi,
I feel myself a bit silly...my nRF52840 board was working the last few weeks nicely, it was visible both in nRFgo and Keil. I had the board some time in button cell...
Hello, after downloading my user app using keil, I can't seem to erase the whole chip.
This is what I'm trying to do:
erase the whole chip (nrf52840).
program S140...
Hello, when migrating a project from nrf51 to S140 nrf52840, I got an
"Error: L6218E: Undefined symbol app_error_fault_handler (referred from softdevice_handler.o)."
...
Hi,
I am quite a beginner about nrf51822. I understand that I can get RSSI during advertise mode before pairing. But I am not sure I can get RSSI after pairing. Can I get...
