Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Written a custom script to write product model no into UICR Registers. After updating Model No, DFU was getting failed at state 6 i.e after updating init data after moving...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
I am trying to sent multiple messages from nrf52dk but it seems that i can sent only 7 even if i put a delay between messages . Any suggestions ?
for(int x =0;x < numberofevents;x...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
I used two PCA10040 boards to test the UART serialization function with s332 softdevice.
I add my ANT_PLUS_NETWORK_KEY and build the examples "experimental_ant_ble" is working...
Hi, I have a strange problem. I am new to nRF IC's.
I recently took a new job...the person who wrote the code for our nRF51422 lost some source code in the process of changing...
I'm trying to create a HID bluetooth device with multiple connections to centrals. Looking at the ble_hids service implementation, the on_connect event handler sets the connection...
Hello!
I'm looking to build an application on nrf52840 DK that collects multiple sensor values and transmits it over Bluetooth. For now, I don't have a bluetooth application...
Hey I'm doing some SPI transfer in response to a GPIOTE in event. I'm targeting the NRF52840 and kind of went with the following answer:
https://devzone.nordicsemi.com...
Hello,
My setup is pca10040, sdk 14.2, s132.
I have tried firstly the blocking mode function and it is not reacting. After that I used SAADC module in a non blocking mode...
Is it possible to use the mbr, currently inside the softdevice, without the softdevice? Can we use the combination MBR/Application/bootloader? So we have a lot more flash...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
When completed my program is supposed to read data from sensor (via I2C), store it in...
