Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
I'm trying to get the TWIM peripheral up and running on a custom board with an NRF52810 running SDK15 and S112.
My board is properly advertising, and publishing our custom...
After nightmares with Eclipse I managed to setup Segger within 5 minutes and flash, using the guide from here .
That guide show a lot of very specific stuff you have to...
I have the following ADC code: bitbucket.org/.../eakpq
I have been trying for the past few days to get this code to just perform a single ADC scan, on five channels, once...
Hi,
I use ble_ant_app_hrm example on 41822.
I set advertising time is 10 secs then I will get a timeout event from stack. When I get this timeout event, I will put the...
Hi
I am trying to use DFU feature using nRF5_SDK_14.2.0_17b948a. I used given preexisted example hex files for bootloader and app and successfully able to use DFU feature...
Develop environment:
BLE: nrf8001(non-connectable mode)
MCU: MSP430F5529
Problem:
I would like to use MCU's timer interrupt to wake up nrf8001 for broadcasting....
I perform some time critical task in my application and sometimes this task fails. Before executing the task I make sure that my device in not in BLE connection and ADV is...
Hi,
I'm looking for an example of how NRFX_UARTE works.
I would like to set up a serial port with EasyDMA to send and receive a thirty bytes.
Thanks in advance for your...
Hello, I am developing ble scanner in which I want to print data of adv reports over uart. Printing is executed in main and in on_ble_evt function I add items to circular...
Hi Expert,
I saw Nordic infocenter said that " HID Keyboard Application is not power optimized! "
I am going to optimize the power consumption,but I don't know how to...
Hello. I am able to send simple text using nRF Connect app to the nrf52832 and write received data to the SD card. So I want to send file (mp3, txt, jpg etc) and write this...
So I've been searching around for an answer to this on these forums and I can't really find what I'm looking for.
I'm using a RedBear BLE Nano v2 to act as an intermediate...
Hello everyone,
I am developing a PCB based on the NRF52 chip, and I need help for the programming interface.
After reading a few threads in the forum, we decided to...
Hi,
I'm using following code, but app_button event is not invoked. I have also enabled the app_timer, app_button and gpiote in the sdk_config.h file. I'm using nrf52832...
