Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
The file nRF5_SDK_1 4.2.0_17b948a/components/libraries/util/app_error_weak.c requires the following modification to correctly compile: Add: #include "app_util_platform.h"...
Hi,
I'm currently using SDK v14.2.0 and I'm attempting to merge the buttonless DFU bluetooth example into the bluetooth template project within the Eclipse Oxygen environment...
Hey Guys,
I have 3 tasks running on FreeRTOS, SDK v14.0.0. In each task, I want to use SEGGER_RTT_printf() to debug.
I currently just call SEGGER_RTT_printf() without...
I have two nrf devices nrf51822 and nrf52DK, In nrf51822 i'm using S110 and i had created a custom service with 10 characteristics. If i connected to nrf connect i can able...
Hi,
Is it possible to make realization of this protocol ( wiki link ) with softdevice? After reading forum I think "more no than yes" because softdevice blocks CPU and this...
Hello
I am still relatively new to microcontroller development with the NRF52 DK. I am currently running a modified version of ble_app_uart__saadc_timer_driven__scan_mode...
I have a Taiyo Yuden Evaluation board , with EBSHJNZXZ completed with Segger and j - link , when load the project in board, not have any error debug, the sketch is load successfully...
I am following this tutorial
I'm using Segger Embedded Studio v3.10i, and SDK 12.2.0. I have the exact same problem in both Linux and Windows.
I have done everything...
What are the details of internal pin connection circuitry when connected as GPIO/IRQ vs ADC vs Comparator? Is there an internal pull down (what value)? Is there internal diode...
what should be RAM Settings for 51822QFAA chip?
I am using nrf sdk for mesh. what should be required ram settings for 51822 in order to run light switch server example....
Hello,
I have problem with missing GPIOTE event. Sometimes event doesn't occur, sometimes there is no problem. This event is very rare but important. I think it happens...
Hi all,
I am working on Temperature and Humidity(DHT11) with nrf52832, After advertising the Bluetooth i am calling the DHT11 sensor function in loop, few seconds it is...
