Hello team,
We have a problem here, we are running a new program with 5 years long-term standby IOT device, once we are trying to use SMS to configure the IOT device we...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
I 've been working with the nRF54L15 for a bit now and it' s been great, but trying to get a bit fancy now and running into problems. I 'm developing with the latest NCS v3...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Why is the "old" EK "not recommended for new designs"? Will the old EK work with the IOT SDK?
(Maybe it is chip rev dependent? I don't have the my EK on hand so I don't...
Hello,
I have purchased a Intel Galileo Gen2 (x86 Arduino) and RedBear BLE shield v2.0. The Arduino IDE I use is Intel's version. I have imported the corresponding libraries...
The application uses bsp_button_is_pressed() but this device has no buttons. This results in err_code set to NRF_ERROR_INVALID_PARAM and subsequently a system reset during...
As previously reported for SDK 7.0.1 here , the documentation for SDK 7.1.0 in:
API Reference/nRF51 SDK/Peripheral Drivers/GPIO and GPIOTE
is missing all info about...
I can't find documentation for the HAL functions in the latest 7.0.1 SDK
Specifically the functions in nrf_gpiote.h
C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Drivers...
Hi,
We are in the process of creating our 2nd pass boards with following components to achieve good RF range>20 meters.
JOHANSON 2450BM14E0003 and SMD Chip Antenna 2450AT18B100...
I have met a problem in communicating with nrf8001.
After reset nrf8001, RDYN is low which means it has something to send. Then I pull low of REQN and start receiving data...
Hi,Nordic:
I use an STM32 to communication with nRF51822 through SPI, and i set the STM32 to master,the nRF51822 to SPI slave, 51822 works as SPIS.
When STM32 send a...
Hello,
I'm working on a custom board based on nRF51822, with keil 5.12 and a segger jlink. I'm trying to setup an SPI connection with the an accelerometer, starting from...
Hi,
I have created a scan response structure containing only the BLE_ADVDATA_FULL_NAME. This is because there in no room left in the advert data to advert the full name...
https://devzone.nordicsemi.com/documentation/nrf51/4.3.0/html/group__app__timer.html
I'm trying to learn from the documentation how the USE_SCHEDULER parameter should be...
Hello Everyone,
right now i use nrf51822 module, now i want to make program for that, so for that i use Eclipse juno, i have download the SDK zip file of version 7.1.0_372d17a_packs...
When I run the nRF51822_beacon_firmware_1.1.0.msi to install the Nordic beacon firmware, the file "beacon.c" under C:\Nordic Semiconductor\nRF51822 Beacon v1.1.0\Source Code...
Hello! I'm trying to program nrf51822 like a BLE device. I'm using QT Creator(QBS) + GNU Compiler + Open OCD + STlink(debugger) to create and to program. What I must to do...
