Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hai team,
Iam using the ble_app_beacon example program.
I found power profiling calculation on this link devzone.nordicsemi.com/.../ .
i calculated power consumption...
Hello,
I installed the new nrfjprog but it fails to write my nrf52 dongle:
ERROR: nrfjprog failed for an unknown reason. Run the same command again with ERROR: argument...
Hello,i want to get the mac address by sd_ble_gap_address_get().There is a error message as fellow: Undefined symbol sd_ble_gap_address_get(referred from main.o). Where is...
HI!
The use of simulation software I2C and the sensor module communication in my program, without the use of the protocol stack, the normal running of the program, but after...
Hello,
I am using sdk 12.2.2 and pca10040. I want to include the mac address in adv packet name. I am not aware of the api used to get mac address. I used sd_ble_gap_address_get...
HW: BMD-350
SDK: nRF5_SDK_12.0.0_12f24da
Sample Code: examples\dfu\bootloader_secure\pca10040_debug
I have my own firmware app.
Problem:
If I use Keil to flash...
Do I have to temperature dissipation? I attached temperature sensor on my board with nrf51822. I removed copper layer of around the temperature sensor. But it seems the temperature...
Hi,
I am using nrf51822(qfaa), sdk12.3, softdevice s130.
I am using the ble_app_uart (both central and peripheral) as reference for my development.
I have both central...
Hi,
I get following error when i try to compile nRF5_IoT_SDK_v0.9.x for target nrf52822
compiling x509_csr.c...
assembling arm_startup_nrf51.s...
(13): error: A1517E...
I'm working with LEDs in a ble example
I'm calling ble_notification_init() and activate the LED in the callback handler.
I get sd_nvic_ClearPendingIRQ, sd_nvic_SetPriority...
Is there a way to get the RSSI value of a message using the standard functions within the sdk for mesh. I am currently using a modified version of the simple_on_off client...
Hi all
I'm trying to send 180 bytes using sd_ble_gattc_write(). Writing 20 bytes at a time with the BLE_GATT_OP_WRITE_REQ write_op works. But now I'm trying to speed things...
When I tried S110 examples like BLE proximity, beacon and hrs on QFAC, it works without any problem. Unfortunatelly I can not see any activity on pin VDD_PA of CDAB. Is there...
Hello.
I used NRF51822 Dongle(Central) and Peripheral.
I want to change from Dongle(Central) to PC(Central).
PC version is window8.1.
but not operation bluetooth communication...
