Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
From document [Getting started with the nRF52840 Preview Development Kit]
( www.nordicsemi.com/.../Getting-started-with-the-nRF52840-Preview-Development-Kit)
we know that...
Hi,
I'm looking for a BLE device to work with an arduino and to speak with a smartphone.
The point is that the connection should be made by the user via the smartphone...
I am using nrf52 with sdk11. I have set the advertiser data as Manufacturer data in nrfConnect app in my android phone. So that whenever the data from my phone is advertised...
Hi.
I try run "ble_app_hids_mouse" example from nRF5_SDK_11.0.0 in nrf51422 (nrf51 dongle).
Previously i ran this example in nrf52 (nrf52 DK, s132 SoftDevice), and all worked...
Hello!
We use chip nrf52832(QFN-48) in our project and we wont to pass the PCB certification.
But we also want to use chip nrf52810(QFN-48) in another project, but with...
Hi ,
Please advise, what the Low Power option I have if I want to sample Two channels of analog input at the same time. The sample rate in every channel is 12K, 12Bit....
Hi I am using SDK12.2.0 and Softdevice S130 v2.0.1 on board PCA100028 ; the board works fine and Phone can scan the name of DFUtarg； But when run the same on the customer...
Hello, I'm planning to try the NordicBlog; Capacitive Touch on the nRF52 series to test a button type or a up-down slider type .
I'm planning to use an nRF52832-QFAA for...
Hello,
Can you please provide any link or give me any advice how to connect NRF51822 chip with NRF51DK?
Here is my connection that doesnt work:
DK GND DETECT and GND...
float f = 1.234;
NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(f)));
How to simplify this way to show float number by uart in sdk13.1.
In...
I have 2 questions regarding BLE5 on nRF52832
Which Soft device and SDK has to be used to implement BLE 5 on nRF52832? We will be using the nRf52 DK for same.
Is the provision...
Hi,
I am using timer interrupt in my code. In that I will be generating interrupt after certain time interval, after the interrupt it should process the incoming data from...
Hi
We are using the nRF52840 and the application is OK now. Then I do the OTA using a Android phone which supports Bluetooth 5 and it's made in our country. I use the nRF...
