Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
Hello dear Nordic Semiconductor!!! I took your wonderful Thingy:52 everything was great until I wanted to build a project based on your Thingy: 52-SDK. I have nrf52840 pdk...
hi, i am having a doubt. now my nrf 52840 is acting as a peripheral. it is advertising some packets and my mobile is acting as a central and receiving the advertising packets...
Hi there,
First: I’m a newby, just did some things with Arduino to control some LEDs etc but not much more before.
What’s my plan: I actually ‘ld lik to control some...
I am new to BLE development and have started by installing SEGGER Embedded Studio
Release 3.30 and have a J-LINK edu usb device and a Core51822 board from Wavetek.
I understand...
I am using various sensors to build a wireless sensor network. There are libraries for sensors that are provided by developers such as from adafruit or sparkfun. I have been...
What is the easiest way to use Arduino libraries into nrf52 projects in Keil on C?
Arduino has a lot minus : bad ide, not support debug mode, not optimize code size. But...
I work with nRF52832, based on SDK 14.0.0, and I have done DFU operation successfully with nRF connect on iOS, but when I used Android phone, nRF connect couldn't start DFU...
ble_app_gls_pca10056_s140.hex
Hi,
I am new in this field and i am trying to do current measurement on the nrf52840 PDK using PPK, in sleep mode(sd_power_system_off) i...
Hi,
I have just bought an nRFGo Motherboard (nRF6310) to develop for the nRF24LE1 (nRF2722). I was able to run some example code on the chip like toggling a pin. Next I...
Hello,
I have an application based on SDK 11 and Softdevice v2.0.0. Also there is a legacy bootloader from SDK 11 for performing DFU.
I am wondering whether it is possible...
