Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi
I'm trying to get an ANT example running on the PCA10028 but I can't make it work.
All supplied make files are for nrf52 based boards.
As I understand it, I need to...
I have tried many different initialize setting, however the ACK could not be received in pine 1 to 5. The PRX can receive all of the 6 pipes. It works for pipe 0 only. Would...
Hello, sorry if this is a stupid question.I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.I want to modify ble_app_hids_keyboard
to be able to send Volumn_up/down keys to android...
Hello:
I am use nrf51822 to transfor data (BLE <->UART),i need a faster rate in ble , and i found a way in the zone,that to use BLE_EVT_TX_COMPLETE to send data, the send...
I would like to use the A/D converter to monitor the battery voltage and need to know if the 0.6V reference is generated with a bandgap or some sort of divider network.
...
Hi,
Next problem I've experienced is jumping processor to Hardfault state at sd_ble_gap_adv_start
with whitelist and BLE_GAP_ADV_FP_FILTER_CONNREQ .
In case adv_params...
Hi
Although I followed and got working eclipse Mars on win10 using this great @Vidar tutorial I am still having problem creating a new project under eclipse for any of...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...
Hi, I just started working on nRF52 with Bluetooth, and I have some concerns about DFU and security.
I’m working on a product equipped with an nRF52 and a MEMS microphone...
Hi!
I am using the NUS service and I noticed that Android 6 (Marshmallow) will not go faster that 47.5 ms. Even iOS can go to 30ms. My target is 7.5.
Am I doing something...
