Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Custom nRF51822
SD130
SDK V11
So sometimes my disconnects seem to fail, the return code says success, but when I try to reconnect I get an error 18, NRF_ERROR_CONN_COUNT...
Hi,,
In the GPIOTE example code(I use TIMER2), I want to control the cc register values by accessing the TIMER2_IRQHandler routine. I tried enabling the interrupt for compare...
I found there is no ble_app_hrs_rtx PCA10040 ,
and release note said:
nRF5 SDK v11.0.0
Heart Rate Application with RTX: Support for nRF52 has been removed.
...
Hello,
I have some MDBT40 modules from Raytac that are blank. I want to flash some code (anything at this point) using the STLink/V2 programmer , SWD interface, and OpenOCD...
So I've got my device running, set up two services with some read and write characteristics and it all works like charm now.
But now I want to react to values written into...
I am using GPIOTE to response to transitions in some GPIO pins. This code is added to the BLE UART example code (ble_app_uart_c with S120) from SDK 10. The code is already...
Hello
I have some trouble with my DFU bootloader, because I changed the BOOTLOADER_REGION_START.
This is, because I need some more space for bootloader.
Do I have to...
Hi,
Hardware:PAC10040
Platform: nRF5_SDK_11.0.0_89a8197
Master Control Panel: V4.1.3
1.If dfu has started and transported some data, then disconnect bluetooth and...
I was able to setup gazell frequency hopping communication between a device and a host. Device:nrf51822+PA/LNA(RFX2401);Host:nrf51822+PA/LNA; They can communicate at a long...
Dear sir,
can you provide any chip which is having RSSI and compatible with NRF24LE1 .We have an application in which we have already have a transmitter based on NRF24LE1...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_uart_c" as reference.
As "ble_app_uart_c" source code, it already knows Service UUID.
uint32_t ble_nus_c_init(ble_nus_c_t...
Hi!
I'm trying to get the MPU-9250 chip working through SPI with my nRF52832. But I don't seem to have much luck.
I have created a basic program for testing, based on...
I am using SDK9.0 to develop a ANCS project,now it accept the incomming call ,message,QQ,Wechat successfully,but the question is how to distinguish the message,QQ and Wechat...
I looked at the radio project in the peripheral folder on SDK5 11. I managed to get a custom radio project that works well with my device. A brief on my project, I set up...
Hi
I have set the nRF Beacon app to action a Tasker task when the phone is "At the beacon".
The app display the following: "An error occurred when launching the task"...
