Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I made a pulse oximeter product with nrf51822AC(base on SDK5.2.0 & S110 6.0.0), and implemented SIG GATT-based profile(PLXP+PLXS). Now we want to do BQB RF PHY testing to...
I have an example combining BLE, UART and SPI in which I use RTT to watch the startup process.
The SoC is nRF52 (BLE Nano2); building with armgcc.
This works ok when JLink...
Hi,
I need to send large data(about 200KB) from android phone to my custom board.
Connected like this :
Android Phone ->(BLE) -> nRF51822 ->(UART) -> Custom board...
Hey everyone,
I'm new to the Nordic/Thingy/Embedded world and was hoping I could get some hand holding to achieve a simple change.
I would like to change the Thingy...
Hi All,
I am working printer project where i will be using two boards , one is nrf51 dongle which acts as client(sends/advertise the data) and another is nrf51422 soc on...
Hello community,
I did a central device which is connecting with 8 slaves and this slaves are sending every time 8 bytes when they are connected. My set up is the following...
I'm trying to create a program that takes a stream of UART data at 115k baud streaming in and sends it over BLE as fast as possible. So far, I've
(1)Verified/ made some...
Dear Nordics,
If I add ble_nus service to buttonless_dfu example , it will reset after ble_dfu_init(). If I set
*p_ble_enable_params->common_enable_params.vs_uuid_count...
I am working on S140 on nRF25840. I am using the ble_app_beacon sample.
I want to set the advertising interval smaller than 100ms while using non-connectable mode. But the...
I am developing a product where I need to read a signal from an SPI ADC and send remotely to a receiver. This will be powered of a coin cell.
I see that the NRF51422 is low...
Hi,
I am trying to program nrf52 (on board ), but I keep getting these error:
$ nrfjprog -f nrf52 --program nrf52832_xxaa.hex --eraseall
ERROR: JLinkARM DLL reported an...
Hi,
I'm trying to connect and discover services of a BLE device equipped with a nrf52832. The device advertises correctly and i can see it on the nrf Connect app on both...
Hi All,
i would like to know how gpio relate to gpiote,i go through some code and find
out , that gpiote handles in,out,config registers that is handle by gpio also ...
Hi nordic guys,
I have built a project based on ble_app_hids_keyboard demo in SDK12.3.0.This is a new hid deive which is microsoft defined in win10.The sample report is...