I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm trying to update attribute value and notify it to client using sd_ble_gatts_hvx() function:
memset(ms, 0, sizeof(params));
params.type=BLE_GATT_HVX_NOTIFICATION;...
When I use sd_ble_gatts_hvx() to send data to iOS and Android device I meet a problem:
Data send to iOS ok,but will return error 8 (invalid states) when send to Android...
Hi,
I am trying to use SPI to get data from a sensor. In nRF 5 SDK V11, I got it to work by setting the SS pin in the config struct of the initialization function.
...
I guess the answer is yes, because I know Characteristic Declaration (UUID 0x2803) has an unique handle for each characteristic.
Just wanted to confirm.
Its the first time I use simple_timer. I do not use the Softdevice. So I'm working with the peripeheral simple_timer example(SDK11).
I know from the app_timer, that every...
Hei!
I recently added WDT to my existing project. After that the normal behavior/sequence of code is not as it is supposed to. Strangely it works okay every other run now...
I just get DK P10040, I am using SDK_11.0.0_89a8197/s132_nrf52_2.0.1_softdevice.
I tried ble_app_uart, it works.
But I find a problem, I cannot set P0.09/10/12/13 high or...
I'm trying to compile nRF51 SDK 8.0.0 under Windows.
So for that purpose I'm going to components/toolchain/gcc and running 'make' there.
No targets specified and no makefile...
Hello,
I find in your source code contradictory values for the UART TX and RX characteristics.
E.g. have a look at nRF toolbox (both Android and IOS) definitions: github...
Hi all,
I am trying to implement DFU on my device with marginal success. Here are the steps that cause the issue:
Using nRFgo Studio: "Erase all", "Program Softdevice...
hi
I use S130 from nRF5_SDK_11.0.0_89a8197 as an ble central base on ble_app_uart_c example. when the ble_peripheral change the adv's content(means have data to send),the...
I have been able to follow the instructions in the nrf5 iot sdk to connect my nrf52 dk to a raspberry pi, however I am unsure why a connection must first be made before I...
Hi,
I'm using nrf52 with S132. I noticed high current draw after calling sd_ecb_block_encrypt() function.
After calling function consumption is 6mA and stays at a constant...
Hi,
I would like to read and update value of the characteristic received from AD pin AIN0. I already tested the following code, where I got very weird results (value is...
