Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
Hello, I would like to ask if it is possible, to use the RTC RV-3028-C7 as the external crystal for low-power clock source as in the below design: Currently, we have on our...
This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I tried to build the coprocessor using NCS 2.9.0, but it doesn’t seem to work. Below is my project configuration,are there any additional parameters I need to set?
Hi All, I encountered an issue while trying to use both Bluetooth and ESB in the same application. To clarify upfront: I am not using these protocols in parallel. Also, I...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
There appears to be a bug with commenting in prj.conf. If I do this:
# This is the appearance of the device from the BLE SIG Assigned Numbers List (384 is general remote...
Hi there,
I am currently trying to program a custom PCB equipped with the BMD-380 that has the nrf52480 inside. Sadly, I am now stuck for days with the same issue: It...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
